High Frequency LCR Meter

Key Features :

Measurement parameters Display format - Series or parallel equivalent circuit - all parameters Test conditions

AC Functions
Capacitance (C)
Inductance (L)
Resistance (R)
Reactance (X)
Conductance (G)
Susceptance (B)
Dissipation Factor (D)
Quality Factor (Q)
Impedance (Z)
Admittance (Y)
Phase Angle (Ø)
/B1 (Non-Isolated) Common 0V. Bin outputs 0 to 5V (nominal) with >10mA current sink capability /B2 (Isolated) Common 24V input. Outputs 0 to 24V with >10mA current source capability.

Setup data
Up to 20 instrument setups may be stored locally.

Measurement connections Four front panel BNC connectors permit two, three or four terminal connections with the screens at ground potential.

1J1011 Component Fixture (supplied as standard) allows connection to leaded components and devices. 1J1012 (2 Terminal) and 1J1014 (4 Terminal) fixtures allow connection to surface mount devices.

Measurement accuracy Dissipation factor ±0.0005 (1+D2)**

Quality factor ±0.05 %( Q+1/Q)**

Capacitance / Inductance / Impedance ±0.05%**

*Varies with frequency, drive level and measured impedance

Power supply Input voltage 90 V AC to 264 V AC (Autoranging)

Mains frequency 47 to 63 Hz

Frequency range
6505P 20Hz to 5MHz
6510P 20Hz to 10MHz
6515P 20Hz to 15MHz
6520P 20Hz to 20MHz
6530P 20Hz to 30MHz
6550P 20Hz to 50MHz
65120P 20Hz to 120MHz
Frequency step size: < 1mHz
Accuracy of set frequency ±0.005%

8.4″ VGA (640 x 480) colour TFT with touch panel

Local printer
HP-PCL compatible graphics printing
Centronics / parallel printer port, Epson compatible text / ticket printing

Network printer
HP-PCL compatible graphics printing

Remote trigger
Rear panel BNC with internal pull-up, operates on logic low or contact closure

GPIB interface
External instrument control. 24 pin IEEE 488 connector

USB interface
Two Universal Serial Bus Interfaces
USB 1.1 compliant

VGA interface
15-way D-type connector to drive an external monitor in addition to the internal screen

Network interface
10/100-BASETX Ethernet controller.
RJ45 connector

Keyboard interface
Standard USB or PS/2 keyboard port. Instrument front panel remains active with keyboard plugged in.

Mouse interface
Standard USB or PS/2 mouse port.
Touch screen remains enabled when the mouse is connected.

Bin handler (option)
/B1 Isolated (24 V) and /B2 non-isolated (5 V).
25-way D-type connector


AC Drive level
10 mV to 1V rms*
200 µA to 20 mA rms*
*Varies with frequency
Signal source impedance: 50 Ω nominal
DC Bias (option)
/D1 0 to +100mA dc bias current and 0 to +40V dc bias voltage
/D2 -40V to +40V dc bias voltage

Binning (option)
10 bins with absolute and percentage limits
25 way D-type interface connector

Environmental conditions
This equipment is intended for indoor use only in a non-explosive and non-corrosive atmosphere

Temperature Range
Storage -20°C to 60°C
Operating 0°C to 40°C
Full Accuracy 18°C to 28°C

Relative humidity
Up to 80% non-condensing

Up to 2000m

Installation category
II in accordance with IEC664

Pollution degree
2 - mainly non-conductive

Complies with the requirements of EN61010-1

Complies with EN61326 for emissions and immunity

Height 190 mm (7.5″)
Width 440 mm (17.37″)
Depth 525 mm (20.5″)
Weight 13.8 kg (32 lb)

Order codes and options
6505P 5 MHz Precision Impedance Analyzer 1J6505P
6510P 10 MHz Precision Impedance Analyzer 1J6510P
6515P 15 MHz Precision Impedance Analyzer 1J6515P
6520P 20 MHz Precision Impedance Analyzer 1J6520P
6530P 30 MHz Precision Impedance Analyzer 1J6530P
6550P 50 MHz Precision Impedance Analyzer 1J6550P
65120P 120 MHz Precision Impedance Analyzer 1J65120P

All units are supplied with user manual, 2 m AC power cable, universal component fixture (1J1011) and USB memory

Bin handler /B1
Bin handler ( isolated 24V ) /B2
DC Bias ( 0 to +100mA and 0 to +40V ) /D1
DC Bias ( -40V to +40V ) /D2
Optional Accessories
Surface Mount Fixture ( 2 Terminal ) 1J1012
Surface Mount Fixture ( 4 Terminal ) 1J1014
Certificate of Calibration with results 1JCALRES